Re: How to populate DNS field in Node Details
I spoke with our MS Server group who controls this, and reverse DNS is configured for some of our network ranges, but not all. In the small range I'm looking, and where my above screen shot was taken,...
View ArticleRe: npm network topology juniper switch problems
Hi Richard, I especially need the connections on 2 trunk interfaces, so there is no way to map this?, I could be done manually? regards Diego G
View ArticleHow to change ports used?
I'm trying to set Web Helpdesk to use port 80 instead of 8081, but I must be missing a step. I've already changed the whd.conf to use the DEFAULT_PORT=80 and restarted the WebHelpdesk service, but it...
View ArticleClik here to view.
Set Location based on IP address
Looking for some help, we're using discovery to automatically add new kit into NPM. Is it possible to automatically configure a nodes location based on it's IP Address? Cheers Kevin
View ArticleConnectNow Without Layer 2/3 Topology Enabled?
So my network manager has asked me to create one of the network topology maps with link utilization and all that fun stuff, but one problem. Whenever I go to Network Atlas and create a map and pull all...
View ArticleClik here to view.
Re: Customer unable to add a Note after ticket is closed
Ok, I thought there was an option for that, but for the life of me I cannot find the setting anywhere. I'm sure I'm over looking it somewhere.
View ArticleRe: Install Woes
Did you remove any registry entries? System Firewalls / Anitvirus / HBSS (usually the case for those of us)?
View ArticleProblems sending emails when Solarwinds is installed on WinServ 2012
Hi guys, I´m having problems sending emails when an alert triggers. When a ran some test I was using Windows 2007 and everything was fine. But now some of our clients have installed Solarwinds on...
View ArticleRe: In-place poller upgrade from 2008 R2 to 2012 - any gotchas?
I assume I'll want to deactivate the licenses on the old box before I shut it down, correct?Thanks again!
View Articlewhat object ids (OIDs) does Orion NPM poll for network utilization percent...
what object ids (OIDs) does Orion NPM poll for network utilization percent for BlueCoat proxys status
View Articlewhat object ids (OIDs) does Orion NPM poll for concurrent connections percent...
what object ids (OIDs) does Orion NPM poll for concurrent connections percent for BlueCoat proxys status
View ArticleRe: In-place poller upgrade from 2008 R2 to 2012 - any gotchas?
Your assumption is correct.
View ArticleSAM Issue with Disabling Components
I just noticed and issue that if a component has triggered an Advanced Alert and you go in and disable the component the Alert does not clear and you have to manually go clear it. Has anyone else seen...
View ArticleRe: In-place poller upgrade from 2008 R2 to 2012 - any gotchas?
First time in my life....Thank you!
View ArticleRe: Using F5 to load balance Orion
did you ever get this working and if so what are the setting on the F5 Thanks
View ArticleClik here to view.
Re: In-place poller upgrade from 2008 R2 to 2012 - any gotchas?
I know what you mean. I'm married....that means I assume usually means I'm wrong but don't want to admit it (thankfully my wife is not a thwack member or I'd be dead soon).
View ArticleRe: ConnectNow Without Layer 2/3 Topology Enabled?
>This is not surprising, as I have had Layer 2 and 3 topology turned off on all devices since testing it, because having that spike the CPU on half of my switches every 2 minutes it updates is much...
View ArticleRe: Unknown Devices w/ Correct SNMP Settings (NTM 2.2 RC)
A few different models of the Cisco Catalyst 3560 switches.
View ArticleRe: Is there a specific Application Monitoring Template for my NCM Server?...
Are there any other processes that should be picked up for monitoring is really what I am looking for. My NCM server has processes that my Web Engine / NPM Does not.
View Article