Duplicate DNS Zones
Hello, We have two Domain Controllers and I have added both as DNS Servers to IPAM. Now, each DNS Zone is listed twice, once for each Domain Controller. Is this OK or should I remove one of the...
View ArticleRe: Netapp Powershell monitoring
Bookmarked -While I am not necessarily the biggest fan of tracking hardware status in SAM monitor components - I find more and more reason to use Powershell or CLI in general to extend our support...
View ArticleRe: Re: Re: How can I exclude a volume from alerting about low disk space?
Just to clarify, if you want to exclude entire VMs and you use the labels approach that uidzer0 suggested, it is simply a matter of changing the search query for the Alert Scope like below...
View ArticleClik here to view.
Re: Can we do ping or snmpwalks through the API?
Have you considered the latest version of Engineer's Toolset? You can pick a polling engine and do ping, tracert, etc from the web consoleEngineer's Toolset v11 is generally available
View ArticleClik here to view.
Re: Custom SNMP Device Templates
Several of the Barracuda MIBs already exist within the SolarWinds MIB database, but none for their message archiving solution. These MIBs can be submitted for inclusion in the MIB database by opening a...
View ArticleRe: NPM 11.0 Release Candidate Now Available!
Rob is there any way to monitor from multiple interfaces of a network PAS, or is there a hard limit right now on a single interface per?
View ArticleRe: SAM MAPI User Experience Monitor - Configuration Issue
CDO is installed. The Exchange Web Services User Experience Monitor is a good idea but since it would be testing internal to internal mail routing rather than external to internal (which tests things...
View ArticleRe: SAM MAPI User Experience Monitor - Configuration Issue
The same services that MAPI is reliant upon also need to be functioning properly for Exchange Web Services so I don't see their being a tremendous difference in the availability of one over the other....
View ArticleRe: Event Messages: "Job Engine v2: Worker Processes"
You should begin to see statistics update essentially immediately, though not all will be updated in that time frame. The Job Scheduler will ensure that the polling jobs are evenly distributed over...
View ArticleRe: Re: Re: Re: How can I exclude a volume from alerting about low disk space?
Hi,I was under the assumption that this would target a particular VM that matched the name xxxxx, so I intentionally left it out. However this still excludes all VMs that were alerting about disks...
View ArticleRe: How to combine the results of multiple reports into a single report?
You would need to remake the reports in the web report writer, but it's a heck of a lot simpler than it sounds I would mention that you should check your data retention levels. By default, statistics...
View ArticleTrap / Syslog Suppression
Is there a way to suppress trap or syslog actions from a specific source given a rule that collects traps for all devices? For example, if I have an alert setup to send an e-mail every time a link up...
View ArticleClik here to view.
Re: Polling Intervals - Best Practices
Does anyone know about the best practice?Why most of the polling intervals have been set for 5 mins?
View ArticleRe: Custom Reporting with SSRS
hi have done this, it just requires a litte more time to create the reports until you getting an understanding of the database
View ArticleClik here to view.
Re: No Bash History for Linux Script Monitors?
You can alternatively disable history for a specific individual user account.
View ArticleRe: Alert triggering for nodes down 'Out of Hours'
neil2094 wrote: Possibly this is due to the version code being quite old, 10.1.3 Must be as I tested this on my setup where I took a node down at 8:50am (so out of hours) and I got notified it was...
View ArticleRe: Bought some SolarWinds swag from the thwack store? Show us!
Good suggestions... But if you want a bumper sticker, they are already in the Thwack Store.
View ArticleClik here to view.
Re: Alerting on a group
I see what you are trying to do now. The Group alerts are meant for the overall status of the group, not for individual members of the group. My suggestion to achieve both your grouping and alerting...
View Article